Most plastic worms have a straight line that runs from head to tail that can be used as a reference line to make sure the worm is perfectly straight. You also want to make sure the worm isn’t twisted as you re-enter. Pinch the worm with your thumb and finger, using your thumb to mark the distance from the head so you know where to enter. Wherever the bottom of the hook lines up with the body of the worm is the distance from the head that you want to enter the worm. To do this, hold the hook in the upright position from the middle part of the shank, letting the worm hang freely and in line with the bottom end of the hook.
It’s imperative that you re-enter the worm at the right location to keep the worm looking straight and natural. Once the hook tip is out, slide the head of the worm up the shank and stop when it reaches the eyelet of the hook. You’re now at the most important part of Texas rigging. For basic worms with a round body it doesn’t matter, but for worms that are not rounded and you want the hook to be exposed on a certain side you should take note of where you exit. The side you decide to exit will be the direct opposite side that the hook point will be exposed on when the rig is complete. Next you want the hook point to turn 90 degrees and exit out the side of the worm. A quarter inch penetration is good but ideally you want to match the distance from the eyelet of the hook to where it first bends.
#Texas ripit how to#
How To Texas Rig A Wormįor this example we are using a wide gap hook. To rig it, insert the hook tip straight through the worm’s nose, penetrating about a quarter inch. If your looking for more information on what weights to use for worms visit the Plastic Worms page. There are a lot of factors to consider when choosing weights that won’t get covered here. This will keep the worm from vanishing in to the grass when the weight hits the bottom, giving it a natural slow sink at the tips of the grass. For example if there was grass on the bottom that was 12 inches tall, you might want to peg the weight 14 or so inches from the worm. Pegging to the nose will put the worm right on the bottom, but sometimes having the worm suspend off the bottom a certain distance can be beneficial. There are three ways to utilize a bullet weight: pegged to the nose of the worm, pegged a set distance away from the worm, or sliding freely on the line. How you decided to use utilize the weight will be based on how you want the worm to present itself on the bottom. They slide on the line before you tie your hook and sit at the head of the worm. For the Texas rig, and for most worm rigs in general, you use bullet weights. Weights determine the depth in the water column you wish to target and the rate at which the worm sinks. The video at the bottom of this page will explain that in greater detail.Ī 3/0 or 4/0 size hook works well with most worms but if your looking for more information on choosing worm hooks and hook sizes visit the Plastic Worms page.
You’ll enter at a 45 degree angle with a round bend and straight in with a wide gap. The only difference between the two types of hooks when rigging Texas style is the angle at which you enter the worm with the point of the hook. There are two types of offset hooks: round bend hooks and wide gap hooks. Round bend hooks show a little less hook to the fish but wide gap hooks have a better hook up ratio. While you can certainly Texas rig a worm with a straight shank hook, offset hooks work best at keeping the head of the worm from sliding down the shank. If you want to get everything you need for Texas rigging your worms then check out this Texas Rig Kit on Amazon. You may also want a weight stopper on your line depending on what kind of conditions you’re fishing. This is not a complicated worm rig, and to begin you only need a few things: rubber worms, hooks, and bullet weights. Though many anglers rig their worms “Texas Style” without a weight while using the weedless feature of the rig. It’s used mostly for its weedless properties, along with giving the worm a nice and straight profile. The Texas Rig is by far the most commonly used rubber worm rig.
0 kommentar(er)
